Page 4 and 12 characters, first scan Code 93 — Length Within Range. This interface type is used to attach the scanner between the keyboard and host computer. Hertz; A unit of frequency equal to one cycle per second. See Alternate Rule Sets on page more information about rule sets. The range is from two to thirty times.
|Published (Last):||16 July 2016|
|PDF File Size:||8.24 Mb|
|ePub File Size:||18.93 Mb|
|Price:||Free* [*Free Regsitration Required]|
Gardalkree Page 8 Connecting a Keyboard Wedge Interface In addition to any single character prefix already selected, the Code ID character is inserted between the prefix and the decoded symbol. Whether using it as a hand-held scanner or in presentation hands-free mode in a stand, the scanner ensures comfort and ease of use for extended periods of time.
The following codes must be read three times: This specular reflection can make decoding difficult. When in reduced power mode, the scanner draws less current from its power source. Page 35 Interface cable is loose.
Hertz; A unit of frequency equal to one cycle per second. If the scanner was damaged in transit, contact Motorola Enterprise Mobility Support at one of the telephone numbers listed on page xv.
The scanner combines excellent scanning performance and advanced ergonomics to provide the best value lls a lightweight laser scanner.
In this way, customers using Motorola compliant decoders can control the behavior of the entire system by scanning the necessary parameters only once. The definition of the Graphic User Interface key depends on the attached system Unpacking the Scanner Remove the scanner from its packing and inspect it for damage. The scanner combines excellent scanning performance and advanced ergonomics to provide the best value in a lightweight laser scanner.
No part of this publication may be reproduced or used in any form, or by any electrical or mechanical means, without permission in writing from Motorola. Be advised, selecting this option is an extreme measure against misdecoding severely out of spec bar codes. Disable this to send nothing to the host if a symbol does not decode. See Installing the Interface Cable on page In this mode the keyboard keystrokes are simply passed through. The minimum allowed value is 80 msec and the maximum is msec.
Select one length per rule only. Scan a bar code below to increase the delay when hosts require a slower transmission of data. It is a standard data transmission code in the U. Symbologies 12 — 39 CLSI Editing When enabled, this parameter strips the start and stop characters and inserts a space after the lx, fifth, and tenth characters of a character Codabar symbol. Connect the other end of the RS interface cable to the serial port on the host. The connectors may be different than those illustrated, but the steps to connect the scanner are the same.
Erase Advanced Data Formatting 14 — 7 Erase Use these bar codes to erase criteria, actions, or rules. Aim Duration Enter a leading zero for durations less than 1. Space Select None when no parity bit is required.
Maintenance and Technical Spe Interface cable is loose. This international agency regulates laser safety by specifying various laser operation classes based on power output during operation. The scanner is shipped with the settings shown in the Symbology Default Table on page also see Appendix To change an option, scan the appropriate bar code s provided in the Symbologies Parameters section beginning on page Select Odd parity mamual set the parity bit value to 0 or 1, based on data, to ensure that the coded character contains an odd number of 1 bits.
If the character is not ,s, the cursor does not move i. Table of Contents Add to my manuals Add. Advanced Data Formatting 14 — 13 Code Lengths Define the number of characters the selected code type must contain.
Lz addition to any single character prefix already selected, the Code ID character is inserted between the prefix and the decoded symbol. To change any option, scan the appropriate bar code s provided in the Keyboard Wedge Host Parameters section beginning on page Page 65 The keystroke in bold is sent only if you enable Function Key Maual on page Transmission Timeout 10 — 8 Symbol LS Product Reference Guide Transmission Timeout The Scanner Emulation Host transmits bar code data to the attached decoder and waits for the attached decoder to assert the Decode signal, indicating successful transmission.
Page http: In case of an error, or to change the selection, scan Cancel on page D User Preferences 4 — 5 Laser On Time This parameter sets the maximum time that decode processing continues during a scan attempt.
This parameter provides two options for the length of the laser scanning beam. Related Posts
Motorola LS3408-FZ20005 Product Reference Manual
LS3408-ER Rugged Barcode Scanner Support
Motorola Symbol LS3408 Manuals & User Guides
DS3608-HD/DS3678-HD Ultra-Rugged Scanner Support